Who did this? You or a shop? If it’s a shop turn back around and make them do it properly jeeze. If it’s you, I’d drain some yeah, that much extra can cause things to leak
It’s only half qt over, ain’t gonna leak,hell be fine even if he don’t Adrian it out, and being a. Cmary of that yr, it’ll be burned off Ina month and back to full
There’s no chance an extra half quart will raise the oil that much. I’ve never seen an engine that didn’t have the space for an extra 2 quarts at least
Yeah pretty much every car is different from its capacity to its “bro you put in too much oil and now here’s some aeration in your shit”. I had a mustang that had a capacity of 5 but the crankcase could hold 7 without aeration. 4.6 2V modular
This was exactly why I asked. My car v6 takes 4.5 quarts, I buy a 5 quart jug every single time and with that I fill the filter totally up then dump the rest into the car, it’s always slightly over max.
Though since ownership the car has leaked a small bit of oil when doing oil changes at 5k miles I’ll get about 4 quarts back out, though I promise the other quart slowly is left in my driveway 😅 you can see every exact spot I’ve parked tiny little oil spot
Edit. I should also add that I’ve never noticed any froth or anything odd on my oil cap or in the oil either was just curious due to what I said above, thank you :)
Technically you shouldn’t pre fill filters unless the car has sat for along time. And if you do prefill filters you defiantly shouldn’t pour it in the big hole. You should slowly pour it into the side smaller holes and let it slowly filter through the material otherwise if you get shit in the big hole it will be going straight to your journal bearings.
The odds anything bad happens is super small if you are clean but better to be safe that sorry especially considering there’s enough residual oil in the engine that the 2 seconds at the absolute most it takes to fill the filter won’t be an issue.
But this is as far as I understand atleast. If a mechanic knows more please correct me but this is what I’ve always heard/done.
If it’s fresh clean oil then it doesn’t really make much of a difference which side you pour oil into but whatever makes you feel more comfortable. General opinion is that it isn’t necessary but prefilling doesn’t hurt and most mechanics I know do it as a just in case anyway.
Who did this? You or a shop? If it’s a shop turn back around and make them do it properly jeeze. If it’s you, I’d drain some yeah, that much extra can cause things to leak
It’s only half qt over, ain’t gonna leak,hell be fine even if he don’t Adrian it out, and being a. Cmary of that yr, it’ll be burned off Ina month and back to full
This isnt that far over to cause leaks
Leaks no, high enough to get above the windage tray and cause the crank to aerate to oil. Definitely
There’s no chance an extra half quart will raise the oil that much. I’ve never seen an engine that didn’t have the space for an extra 2 quarts at least
Half a quart over is definitely into the crank??
Now would this be something of concern?
If it leaks into your spark plug connector bays you will find out. Depends on the engine exactly what might happen.
Yea, it makes the oil froth up, and then it doesn’t lubricate correctly
Yes, but I think it’s that it can’t be pumped correctly by the oil pump and therefore will leave the parts of the engine starved of oil.
That’s more or less part of what I meant as well. It doesn’t lube properly because it’s foamy but also doesn’t flow.
Yes, because it introduces bubbles in the oil and causes it to lose some lubrication capacity.
But how much is too much depends on the engine and how much you go over the limit. It is unlikely to happen if you go half a quart over the limit.
Yeah pretty much every car is different from its capacity to its “bro you put in too much oil and now here’s some aeration in your shit”. I had a mustang that had a capacity of 5 but the crankcase could hold 7 without aeration. 4.6 2V modular
This was exactly why I asked. My car v6 takes 4.5 quarts, I buy a 5 quart jug every single time and with that I fill the filter totally up then dump the rest into the car, it’s always slightly over max.
Though since ownership the car has leaked a small bit of oil when doing oil changes at 5k miles I’ll get about 4 quarts back out, though I promise the other quart slowly is left in my driveway 😅 you can see every exact spot I’ve parked tiny little oil spot
Edit. I should also add that I’ve never noticed any froth or anything odd on my oil cap or in the oil either was just curious due to what I said above, thank you :)
Technically you shouldn’t pre fill filters unless the car has sat for along time. And if you do prefill filters you defiantly shouldn’t pour it in the big hole. You should slowly pour it into the side smaller holes and let it slowly filter through the material otherwise if you get shit in the big hole it will be going straight to your journal bearings.
The odds anything bad happens is super small if you are clean but better to be safe that sorry especially considering there’s enough residual oil in the engine that the 2 seconds at the absolute most it takes to fill the filter won’t be an issue.
But this is as far as I understand atleast. If a mechanic knows more please correct me but this is what I’ve always heard/done.
I thought oil flowed into the big hole where it screws in, was pressurized and the flows out the side holes.
If it’s fresh clean oil then it doesn’t really make much of a difference which side you pour oil into but whatever makes you feel more comfortable. General opinion is that it isn’t necessary but prefilling doesn’t hurt and most mechanics I know do it as a just in case anyway.
Every time I’ve changed my own oil the filter had instructions to fill it with oil before installing it.
Yes, it can cause oil pressure drop and/or lubricity issues